![]() Press the plus (+) button to change between ON and OFF (if you observe DST it must be ON – even in the winter). Press SET 2 times: Daylight Savings (DST): The time will change to ON or OFF.If you have the number without a minus sign, keep pressing the + button until you see the abbreviation of your time zone in the day of week display, a minus sign in the month display, and your time zone number in the day display. The US time zones must have a minus sign. Press the plus (+) button to change to the proper time zone Press SET 1 time: Time Zone: The time zone will flash in the date display.Then press and release the PLUS (+) button while still flashing to change to the desired setting.Press and release the SET button as many times as indicated until the function you wish to change begins to flash.If you want to change any of the functions, follow the simple instructions below. All of the other functions are already programmed. Please note that the ONLY function you need to program is the time zone if you do not live in the Eastern time zone. If you have a different model, please refer to the manual by clicking here: If you have the digital 4-button (SET, +, ALM, SNZ) model clock, you may use the following instructions to set your clock. Ensure that the batteries used are new and the correct size.HELPFUL INFORMATION ABOUT YOUR SKYSCAN DIGITAL ATOMIC CLOCK BATTERIES CHANGE: For best performance, batteries should be replaced at least once a year to maintain the best running accuracy. Defective clocks should be returned to the place of retail purchase. This model is discontinued and not eligible for the manufacturer’s warranty. WARRANTY: This product is warranted to be free of defects in manufacturing for 90 days after purchase from Sams Club. Make sure the clock is at a receivable range from the transmitter. 2) Move the Atomic Clock closer to the transmitter or place the transmitter closer to the Skyscan Atomic Clock. Make sure the batteries are new and fresh. 1) Remove the batteries of both units for one minute, then reinsert them again. Problem: Solution: Problem: Solution: "-.-" appears in the outdoor temperature section of the LCD. Once the foldout table stands are extended, place the Atomic Clock in an appropriate location. ![]() The hinges are towards the edges of the SkyScan Atomic Clock, and the ends (with no hinge) need to be folded out towards the edge. POSITIONING THE ATOMIC CLOCK: There are two possible ways to mount the Atomic Clock: use of the foldout table stands, or wall mounting FOLDOUT TABLE STANDS The foldout table stand legs are located on the backside, at the lower corners, and on both sides of the battery cover. ALARM SETTING To enter into the alarm setting mode: 1. If no keys are pressed for at least 15 seconds in setting mode, the Atomic Clock will automatically switch back to normal display mode. Now the minute digits will start flashing.ĮXIT THE MANUAL SETTING MODES To return to the normal display mode from anywhere in manual setting mode simply press the SNOOZE key anytime. Set the desired hours by pressing the + key followed by pressing the SET key. The hour digits will start flashing on LCD1. Note: In 12 hours mode the time will be displayed with an additional “PM” for the time from 12:00 noon until 11:59. The clock will then work as a normal Quartz clock. MANUAL TIME SETTING In case the SkyScan Atomic Clock is not able to detect the WWVB-signal (disturbances, transmitting distance, etc.), the time can be manually set. After completion of the above described procedures in “Setting up” the manual setting modes can be entered by pressing the SET key. MANUAL SETTINGS Note: If the Atomic Clock has already successfully received the WWVB time signal and displays the correct time and date, then the Manual settings can be omitted. 1.ĪTOMIC CLOCK LCD SCREEN DESCRIPTIONS The Atomic Clock's LCD is divided into 2 sections and once the batteries are inserted, all the segments will light up briefly before displaying the information for time, date, indoor and outdoor temperatures. SETTING UP: Do not set the clock until the outdoor temperature is displayed. Insert the batteries, observing the correct polarity (see marking). To install and replace the batteries, please follow the steps below: 1. TO INSTALL AND REPLACE BATTERIES IN THE TEMPERATURE TRANSMITTER The transmitter uses 2 x AA,1.5V batteries. Operation of this product is simple and straightforward. Providing WWVB radio-controlled time, date, time zone, indoor and outdoor temperature display, this innovative clock is ideal for home or office use. ![]() SKYSCAN ATOMIC CLOCK WITH OUTDOOR WIRELESS TEMPERATURE MODEL 86722 Instruction Manual INTRODUCTION: Congratulations on purchasing this state-of-the-art Skyscan Atomic Clock as an example of superior design and engineering.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |